Traveling Sprinkler | 58322

Propulsion & Operation

• Self-propelled by water pressure; no electricity required
• 3-position speed control: High (37 ft/hr), Low (21 ft/hr), Neutral (stationary)
• Automatic shut-off ramp placement anywhere along hose to stop sprinkler at desired location

Coverage & Water Application

• Maximum coverage area: up to 13,500 square feet (with 200 feet of hose)
• Spray diameter range: 15–55 feet (adjustable via arm positioning)
• Water application rates: ¼" per pass (High gear), ½" per pass (Low gear), or ⅓"–¾" at 30-foot width depending on pressure and speed
• Travel distance capacity: up to 200 feet of hose per cycle

Hose & Connection Requirements

• Compatible hose size: 5/8" diameter
• Requires minimum 3-foot loop at hose end to prevent pinching
• Works with any hose pattern: straight lines, curves, complex layouts

Spray Arm Specifications

• Adjustable arm positioning for coverage customization
• 15-foot width: ⅔"–1" water application (High/Low)
• 30-foot width: ⅓"–¾" water application (High/Low)
• 45-foot width: ¼"–½" water application (High/Low)
• 55-foot width: 3/16"–¼" water application (High/Low)
• Narrow spray option: arms pointing downward
• Wide spray option: arms pointing approximately 30 degrees upward
• Windy conditions: horizontal arm position recommended

Construction & Durability

• Body material: Rust-proof cast iron
• Finish: Powder-coat paint for weather resistance
• Designed for grass lawns only; not for use on concrete driveways, sidewalks, or hard surfaces

Performance Specifications

• Minimum water pressure: 40 psi (average)
• Spray type: Rotary spray arms for even water distribution
• Filter washer included at hose coupling; must remain clean and unblocked
• Drainage: Stand on end for 5+ minutes after each use to eliminate interior water

Maintenance & Storage

• Keep filter washer clean and spray arms unobstructed
• Do not force sprinkler movement during operation
• Avoid miring in thick grass or mud
• Allow full drainage before repositioning

Warranty

• 6-year limited warranty on materials and workmanship from date of purchase
• Covers defective parts replacement under normal use and service
• Not responsible for consequential or incidental damage from product failure

Safety & Restrictions

• Not intended for use by young children
• For outdoor use with cold water only
• Do not spray near electrical connections

Preventive Maintenance

Filter washer cleaning

Inspect the filter washer at the hose coupling before each use. Remove debris or sediment with a soft brush. A clean filter prevents weak spray and protects internal components from clogging.

Post-use drainage

After each watering session, stand the sprinkler upright on its end for at least 5 minutes to fully drain interior water. This prevents rust formation in the gearbox and extends component lifespan.

Avoid stress on the gearbox

Residential use (intermittent watering, standard water pressure 40–60 psi, hose lengths up to 200 feet) supports 6+ years of reliable operation. Daily continuous use, pressures above 80 psi, high-flow hoses, or exceeding 200 feet of hose length accelerate gearbox wear.

Lawn surface inspection

Before each use, check the path for bare spots, rocks, thick mud, or debris. The cast-iron body is designed for stability, but running over hard surfaces (concrete, gravel) or getting stuck in soft ground can damage the motor assembly. Use on grass only.

Troubleshooting

Sprinkler won't move (but spray arms spin and water flows)

Check arm positioning: Spray arms must point in opposite directions and be turned counter-clockwise (loosening direction) to engage the drive mechanism. If arms are aligned parallel or pointing in the same direction, the sprinkler will spray but not travel. Reposition arms so they angle away from each other, then test again.

Weak or uneven spray pattern

Likely cause: clogged nozzles or filter washer. Remove the nozzles from the spray arms and soak in a 1:1 vinegar and water solution for 30 minutes. Use a soft brush or toothpick to clear debris. Rinse thoroughly. Check the filter washer at the hose coupling and clean with a brush. Low water pressure or undersized hose (less than 5/8") can also reduce spray; verify your water supply pressure is at least 40 psi.

Leaking from bottom housing

Expected wear item. Minor seepage from the bottom housing is common after extended use (3–6+ years depending on frequency and pressure). If leaking is heavy or affects operation, the unit may be approaching end of service life. Contact Orbit customer service at 1-800-488-6156 to discuss replacement or repair options.

Gear noise or jerky movement

Potential gearbox wear. Unusual grinding, clicking, or uneven travel suggests internal gear wear, particularly if the unit is 4+ years old or has experienced heavy use. Drain the sprinkler fully and allow to rest for 24 hours, then test again. If noise persists, the gearbox may require service or replacement. Contact support for options.

Shut-off ramp doesn't stop the sprinkler

Check ramp placement: Ensure the ramp is flat against the hose and positioned so the sprinkler will fully contact it. The ramp should have at least 5 feet of straight hose on either side. If the ramp is too close to hose curves or kinks, the sprinkler may bypass it. Reposition the ramp and test with reduced pressure if needed.

Sprinkler travels beyond intended area

Likely cause: flimsy shut-off post. The plastic post may lift out of the ground, especially on soft soil or sloped terrain. Push the post firmly into the turf at a slight angle away from the hose path to increase grip. If the post is cracked or broken, replacement parts are available through Orbit customer service.

When to Contact Support

If troubleshooting steps don't resolve the issue, or if the sprinkler is within the 6-year warranty period and requires parts replacement, contact Orbit customer service using the chat icon in the bottom right of your screen.

Have your receipt and model number (58322) ready.